Eizo FlexScan L362T Instrukcja Użytkownika

User’s Manual Touch Panel Color LCD Monitor It shall be assured that the final system is in compliance to IEC60601-1-1 requirements.

English 1-3. Controls & Connectors Front S I G .S I G .AUTOAUTOENT.ENT.(4) (5)(6)(7)(8)(3)(1)(2)SIG.AUTOENT. Control Panel (1) ScreenManager® (2)

English Rear (10)(9)(11)(12)(14)(15)(16)POWER INPUTDVID-SUB(13) Bottom (9) Power Connector (10) RS-232C port (Mini DIN 6 pin) (11) External line i

English 2. CABLE CONNECTION 2-1. Before connecting Before connecting your monitor to the PC, change the display screen settings (resolution (p.37) an

English 2-2. Connecting the signal cable NOTE • Be sure that the power switches of both the PC and the monitor are OFF. 1. Plug the signal cable int

English 2. Plug the enclosed touch panel cable into the RS-232C port of the monitor. Then, plug the other end of the cable into the COM port of the

English 2-3. Connecting two PCs to the monitor Two PCs can be connected to the monitor through the DVI and the D-Sub mini 15 pin connector on the bac

English 3. ScreenManager 3-1. How to use the ScreenManager S I G .S I G .AUTOAUTOENT.ENT.SIG.AUTOENT. 1. Entering the ScreenManager Press the Enter B

English 3-2. Adjustments and Settings The following table shows all the ScreenManager’s adjustment and setting menus. “*” indicates adjustments of an

English 3-3. Useful Functions Adjustment Lock Use the “Adjustment Lock” function to prevent any accidental changes. Locked function • Auto Adjustment

English EIZO Logo disappearing function When switching on the Power Switch on the control panel, the EIZO logo is displyed for a while. If you desire

English SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to

English 4. ADJUSTMENT The monitor displays the digital input image correctly based on its pre-setting data. Adjust the brightness (p.23). 4-1. Scre

English 2. We recommend setting the desktop pattern to that as shown in the diagram below. NOTE • More precise adjustment is available for using

English (3) The screen position is incorrect. → Use the <Position> adjustment. The correct displayed position of the monitor is decided bec

English 6. To Set the Brightness of the screen. → Use the <Brightness> adjustment. The brightness of the entire screen is controlled by chan

English 4-2. Color Adjustment The <Color> menu in the ScreenManager enables to change the color of the screen. By using the <Color Mode>

English Color Mode Menu Custom sRGB Function Descriptions Adjustable range To change the saturation -128 ∼ 127 Setting the minimum level (-128) tu

English 4-3. Power-save Setup The <PowerManager> menu in the ScreenManager enables to set the power-save setup. NOTE • Do your part to conserv

English Power save for speaker When the monitor is in the power-saving mode, sound of speaker also erases simultaneously can be performed. [Procedure

English 5. ATTACHING A STAND The LCD monitor can be used with other stand by removing the tilt stand and attaching the stand to the LCD monitor. NOTE

English 6. TROUBLESHOOTING If a problem persists even after applying the suggested remedies, contact an EIZO dealer. • No picture problems : See No

English TABLE OF CONTENTS PRECAUTIONS ...4 1. INTRODUCTION ...

English Problems Points to check with possible solutions 3. Display position is incorrect.  Adjust the image position using the <Position>

English Problems Points to check with possible solutions 10. The <Smoothing> cannot be selected.  <Smoothing> is disabled when the scr

English • Touch Panel problems Problems Points to check with possible solutions 14. Cursor is jittery. / Drawing lines are not straight and smooth

English 7. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. NOTE • Never use thinner

English 8. SPECIFICATIONS LCD Panel 38 cm (15.0 inch), TFT color LCD panel with Anti-Glare Hard Coating, Viewing Angle: H: 170°, V: 170° Respons

English Temperature Operating: 0 °C ~ 35 °C (32 °F ~ 95 ° F) Storage: -20 °C ~ 60 °C (-4 °F ~ 140 ° F) Humidity 30% to 80% R.H. Non-condensing En

English Pin Assignment D-Sub mini 15 pin connector Pin No.Signal Pin No.Signal Pin No. Signal 1 Red video 6 Red ground 11 Ground Shorted 2 Green

English 9. GLOSSARY Clock With the analog input signal display, the analog signal is converted to a digital signal by the LCD circuitry. To convert t

English Phase The phase adjustment decides the sampling timing point for converting the analog input signal to a digital signal. Adjusting the phase

APPENDIX/ANHANG/ANNEXE Preset Timing Chart for Analog input Timing-Übersichten für Analog Eingang Synchronisation des Signaux pour Analog numerique

English PRECAUTIONS IMPORTANT! • This product has been adjusted specifically for use in the region to which it was originally shipped. If operated ou

For U.S.A, Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland D

Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standa

Recycle Auskunft Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland zusammen mit dem Partner eds-r gmbh rucknahmesysteme.

English WARNING If the unit begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections imm

English WARNING To avoid danger of suffocation, keep the plastic packing bags away from babies and children. Use the enclosed power cord and con

English WARNING When attaching an arm stand, please refer to the user’s manual of the arm stand and install the unit securely with the enclosed s

English CAUTION Use an easily accessible power outlet. This will ensure that you can disconnect the power quickly in case of a problem. Periodica

English 1. INTRODUCTION Thank you very much for choosing an EIZO Color Monitor. 1-1. Features • Dual inputs compliant • DVI (p.37) Digital input